NovAsia

Modelling Cooling Costs from Thai Energy Labels

Nova Asia AI assistant

Let’s explore this page together

Published · Updated

KEY TAKEAWAYS

What to take away

4 points · about 35 sec

The main ideas to keep in mind as you read.

  1. The baht-per-year figure on a Thai No.5 label comes from standardised operating assumptions, not the household’s electricity tariff. A 2026 label uses 2,920 hours and THB 5/kWh, which may bear little resemblance to a tenant’s schedule.

  2. A monthly cooling estimate needs an energy figure before it needs a price: average electrical input multiplied by operating hours gives additional kWh. Those kWh then enter the bill alongside existing household consumption.

  3. In the article’s 250-kWh household scenario, 180 hours of cooling adds THB 208.04–838.58 across four assumed loads under the specified September–December 2026 PEA tariff; these are sensitivity results, not typical bills.

  4. A precise air-conditioner model code and a real electricity bill are more useful than a generic star rating or a landlord’s verbal estimate.

Why the label cannot predict your apartment bill

A rental listing might describe an air conditioner as cheap to run and point to the No.5 energy sticker as proof. The sticker even gives a yearly figure in baht. Yet the number on a tenant’s electricity bill is likely to look quite different, even when the unit is functioning normally.

The annual amount on a current Thai air-conditioner label is more specific than an advertising claim, but it comes with assumptions. EGAT’s 2026 air-conditioner programme manual calculates the annual estimate using eight operating hours a day, or 2,920 a year, and an assumed electricity price of THB 5.00 per kWh drawn from 2023. Neither value describes the evening routine or current bill of a particular tenant. An older EGAT explanation used THB 3.96 per kWh for the same annual operating hours.

There are also two bills people tend to mix up. The electricity supplier sees the whole home: cooling, lighting, cooking appliances, refrigeration and anything else drawing power from the meter. To estimate what cooling adds, we need the difference between a bill with and without the extra air-conditioner kWh, calculated under the same billing rules. Merely multiplying the unit’s advertised cooling capacity by its running time will not provide those kWh.

We will use a six-hour evening schedule over 30 days and hold other household consumption at an illustrative 250 kWh. Four different assumptions about the unit’s average electrical input produce four different additions to the bill. They are chosen numbers, not observed Thai household consumption, and are not claims about any brand or model. The exercise works only for its stated September–December 2026 Ft and a particular PEA residential tariff; a bill issued through a condominium office or landlord may follow a different method.

Before relying on anyone’s monthly cooling quote, it helps to separate the three pieces of evidence it would need: an identifiable appliance, a defensible electricity-consumption figure and the actual payment route.

What Thai energy labels can actually tell you

A useful comparison begins with the model identifier, not the stars. Thailand’s updated No.5 label shows the manufacturer and model, appliance type, cooling capacity, seasonal efficiency and an estimated annual electricity cost; the QR code provides a route to further product information. The 2026 EGAT specification describes six efficiency grades, from No.5 without stars through to No.5 with five stars.

Cooling capacity and power input answer entirely different questions. A unit advertised at 12,000 BTU/h is described by the amount of cooling it can deliver under specified conditions. That is not a 12,000-watt electrical draw. Electrical input is expressed in watts or kilowatts; the energy charged for over time is measured in kilowatt-hours. When an average input of 0.50 kW is maintained over an assumed total of 180 operating hours, the calculation produces 90 kWh.

SEER is the seasonal energy efficiency ratio. Under the current EGAT air-conditioner requirements it is expressed in BTU/h per watt, based on prescribed seasonal testing with ISO 16358-1:2013 or the relevant Thai equivalent among the cited standards. Higher SEER means better cooling efficiency on that common testing basis. It does not mean the compressor draws the same watts each hour after installation.

The comparison has to be like for like. EGAT’s 2026 manual sets different SEER grade thresholds for fixed-speed and inverter units and for different cooling-capacity bands. A five-star sticker on one type therefore should not be treated as numerically identical to five stars on every other type or generation. First compare models with closely matched cooling output, the same broad equipment type and the same labelling rules; then examine their actual SEER figures.

The estimated yearly baht amount can be traced to a published calculation. In the 2026 EGAT manual, declared cooling capacity is divided by declared SEER to obtain an illustrative electrical input, converted to kW, multiplied by 2,920 operating hours and then by THB 5.00/kWh. Crucially, EGAT identifies the price as an assumption from 2023. It is not the newly revised 2026 PEA household tariff and does not include the progressive tariff calculation for your other appliances. EGAT’s 2019 document used THB 3.96 instead.

A datasheet may also show rated input and maximum input in watts. Those figures describe electrical characteristics at specified conditions, and the maximum is not a meter reading that recurs throughout an entire evening. Look for the full model code, and, where relevant, confirm the indoor and outdoor combination. The No.5 QR record and the maker’s exact specification are more reliable than an image copied from a similar product listing. Without a verified model label, the sensible comparison is limited to what these fields mean; there is no defensible claim of a particular model’s monthly savings.

QUESTIONS ABOUT THIS TOPIC

A closer look

4 questions · open to read

Practical follow-up questions that go beyond the basics.

Can I use the air conditioner’s maximum wattage as its average power draw?

Maximum input describes an operating limit, not what the unit draws throughout an evening. Inverter output changes with cooling demand, and fixed-speed units cycle on and off; metered kWh over the actual interval gives stronger evidence than multiplying maximum watts by hours.

How should I compare cooling costs in two apartments with different baseline electricity use?

Use a separate non-cooling baseline for each apartment rather than reusing the illustrative 250 kWh. Add the same cooling kWh, then recalculate each full bill with and without it. Higher starting consumption can push the increment into a more expensive tier. If the apartments are billed differently, replace the PEA example with each actual tariff or lease formula.

What does a newer No.5 label change when comparing an older installed air conditioner?

Check the label revision and full equipment model before interpreting stars or the annual baht figure. EGAT used different electricity-price assumptions in the cited 2019 and 2026 calculations, while star thresholds also depend on technology and cooling-capacity group; a higher sticker cost therefore does not prove lower efficiency. The technical specifications must be compared on a genuinely like-for-like basis.

How can I test a landlord’s claim that cooling adds only a fixed amount each month?

Start by establishing whether the invoice comes directly from PEA or MEA, a building submeter, or a separate lease arrangement; the calculation method matters more than the claimed baht total. Obtain the billing formula and readings, then measure the air conditioner’s kWh over a suitable period if practical. Apply those kWh to the actual billing terms and compare the increment with the landlord’s figure, while recognising that weather, room use and seasons can alter the result.

Which label figures are useful for comparison

A field-by-field meaning check: similar-looking numbers can refer to different things.

FieldOn the labelAt home
Cooling capacity, BTU/hRated cooling output in BTU/h, not electrical watts.Match capacity to the space and its cooling demand.
Seasonal efficiency (SEER)Seasonal test efficiency, expressed in BTU/h per watt.Not the actual average kW drawn during an evening.
No.5 and star levelEfficiency grade for the model type, size and label edition.Older grades and different unit types may use other cut-offs.
Estimated annual cost, THBEGAT 2026 estimate: 2,920 h/year at THB 5.00/kWh.Does not establish your actual kWh or utility tariff.
Electrical input, WRated/maximum input is generally in the model datasheet.Average running input changes with conditions and cycling.
Metered kWh and tariffMeter readings and billing terms are not label data.Use metered kWh and actual tariff, Ft, VAT or lease terms.

Four bills from one cooling schedule

Take one deliberately simple monthly budget. Electricity used by everything other than the cooling we are adding is set at 250 kWh. The air conditioner is scheduled for six hours on each of 30 days, giving 180 operating hours. We do not change the room, the tariff or this schedule between cases. We change only the assumed average electrical input while it is switched on: 0.25, 0.50, 0.75 and 1.00 kW.

Energy comes first. Average input multiplied by running hours gives 45, 90, 135 or 180 additional kWh. Add those amounts to the 250-kWh baseline and the household totals become 295, 340, 385 and 430 kWh. The appropriate price can depend on how much the household has already used during the billing period.

For this calculation we use PEA residential class 1.1.2 under the tariff changes effective from the September 2026 bill. Its energy rate is THB 3.0000/kWh on the first 200 kWh, THB 4.1584 on kWh 201–400, and THB 4.3583 from kWh 401 onwards. A separate Ft adjustment of THB 0.1623/kWh applies to the September–December 2026 billing period. VAT is 7%, the rate extended by Thailand’s Revenue Department to 30 September 2027. The tier rates do not include the standing service charge, Ft or VAT.

Calculate the whole bill twice and subtract, using identical tariff terms. If T(U) is the tiered energy charge for a household using U kWh, the illustrative bill is [T(U) + 0.1623 × U + unchanged monthly service charge] × 1.07. The cooling increment is the result at U = 250 + cooling kWh, less the result at U = 250. Because the monthly service charge is fixed in both calculations, it cancels from that difference.

The 0.50-kW case is easy to audit. An extra 90 kWh falls wholly within the 201–400 band, adding THB 374.256 in tiered energy charges and THB 14.607 in Ft. After 7% VAT, the incremental bill rounds to THB 416.08. At 1.00 kW, the added 180 kWh pushes total household usage to 430: the first 150 additional kWh remain in the middle band, while the final 30 are priced at the higher 401-plus band. The incremental charge, including the relevant Ft and VAT, is THB 838.58.

The four figures in the comparison are not low, average and high forecasts for Thai air conditioners. They are four reproducible outputs from one hypothetical household and one dated tariff. Change the baseline, the bill month, the supplier, or the way the tenant is charged and the baht figures need to be recalculated. If metering has given you a credible additional kWh figure, use that directly; there is no reason to reverse-engineer it from the sticker’s annual cost or a maximum-input specification.

Compare the options

Scenario 1 / 4

Very light load

Average electrical input while operating, kW
0.25
Cooling operating time, h/month
180
Additional kWh/month
45
Total household kWh/month
295
Incremental bill, THB/month
208.04
Scenario 2 / 4

Moderate load

Average electrical input while operating, kW
0.50
Cooling operating time, h/month
180
Additional kWh/month
90
Total household kWh/month
340
Incremental bill, THB/month
416.08
Scenario 3 / 4

Elevated load

Average electrical input while operating, kW
0.75
Cooling operating time, h/month
180
Additional kWh/month
135
Total household kWh/month
385
Incremental bill, THB/month
624.13
Scenario 4 / 4

High load

Average electrical input while operating, kW
1.00
Cooling operating time, h/month
180
Additional kWh/month
180
Total household kWh/month
430
Incremental bill, THB/month
838.58

Why the same running hours can use different energy

A unit can spend much of an evening switched on without drawing the same amount of electricity throughout. On an inverter system, the compressor can reduce or raise its output in response to the cooling demand. A fixed-speed compressor may alternate between running and stopping as the thermostat responds. That is why maximum nameplate wattage multiplied by six hours is a poor description of an unknown night’s energy use, and even the rated input is not automatically the average input.

Consider two otherwise similar bedrooms in one development. The first faces the afternoon sun, has broad glazing and retains heat well into the evening; the second is shaded and has a smaller area exposed to outdoor heat. Both tenants set the same temperature at 6 pm and turn the air conditioning off at midnight. The machine facing the larger heat load may spend longer running hard to bring the space down to the set point. The shaded room may reach it sooner and spend more time maintaining it. The labels can be identical while the kWh differ for understandable physical reasons.

Warm outdoor air enters through an opened balcony door or leaky frame, while moisture carried with that air also has to be removed. Ceiling height, occupancy, heat from cooking and other appliances, insulation, outdoor temperature and installation quality influence the job the system must do. A lower temperature target often increases that job, but there is no responsible universal statement that one degree always changes the electricity bill by a particular percentage. Neither does an inverter label, on its own, justify a promised percentage saving in every room.

Condition and maintenance can shift the result further. Restricted airflow from dirty filters, a fouled heat exchanger or a poorly installed system may impair performance. A clean machine still faces the heat entering its room; cleaning is not a substitute for a suitable cooling capacity and sound installation. The energy label helps compare equipment; it cannot certify the windows, refrigerant condition, airflow or daily habits at a rental property.

A measured number is much more useful when the decision hinges on a few hundred baht each month. A dedicated submeter or a suitable measurement performed by a qualified technician can show how many kWh the air conditioner actually uses over an interval. Watching the entire apartment’s meter over a short period is less conclusive because refrigerators, water heaters and other loads run independently. A few evenings of measurements provide a reality check, not a complete seasonal profile: weather and occupancy may be different next month.

Common mistakes and how to fix them

Multiply peak nameplate wattage by all operating hours

What it costsCreates false precision for a compressor whose draw changes during operation.

What to do insteadSeparate rated and real average power; state assumptions or measure energy use.

Divide the label’s annual THB figure by 12

What it costsQuietly imports standard test conditions and the label’s assumed electricity price.

What to do insteadUse labels to compare models; calculate bills from current rates and explicit usage.

Charge all extra kWh at one headline average rate

What it costsMisses tier crossings, Ft and VAT, particularly above 400 kWh/month.

What to do insteadSubtract bills calculated under the same full tariff formula.

Treat five stars as guaranteed savings in any room

What it costsIgnores cooling capacity, room heat load and the actual installation.

What to do insteadCompare size-matched units and explain the limits of standardised performance.

Which electricity tariff applies in a rental

The tariff in the example is a utility tariff, not a universal price payable by every tenant in Thailand. Before estimating an air conditioner’s effect on rent-related outgoings, it is worth establishing whether there is a direct electricity account, a building-managed submeter, or a separate billing agreement with the landlord.

With a direct residential account, the electricity bill identifies the utility, tariff class and billing period. PEA serves much of the country outside the metropolitan service area, while MEA serves Bangkok and surrounding areas. A useful bill shows meter readings, kWh, the energy charge, Ft, the service charge and VAT; it allows the household total to be recreated. The model on this page uses PEA class 1.1.2. The billing classification and any time-of-use election must match the actual account.

A condominium or serviced residence may instead receive electricity under one master account and issue separate charges to rooms using its own submeters. The tenant may see accurate room-level kWh but have no direct residential utility account. The building’s account category, allocation method and treatment of communal power can affect the invoice. Our PEA incremental calculation does not establish what the building is entitled to bill or what it actually charges.

In another arrangement, the landlord sets out an electricity-charging method in the lease. There might be a per-kWh amount, an allowance built into rent or a separate invoice whose format does not list Ft and VAT individually. Those details change what an additional 45 or 180 kWh means in cash terms for the tenant. A utility’s tariff can explain the cost of electricity supplied to an account holder without settling the legality of a particular resale or rental condition. That question calls for the actual contract and any rules applying to that property, not an assumed legal ceiling inferred from the residential tariff table.

The monthly baseline deserves as much attention as the rate. If the only available document is a household bill showing 340 kWh, that does not reveal how many of those units came from cooling. The 250-kWh baseline here is hypothetical and excludes the additional cooling under consideration. In a real apartment, a prior comparable billing period, a dedicated energy reading, or a carefully documented estimate may be needed to separate cooling from the rest of the home.

For a decision that can stand up to scrutiny, connect a complete AC model code and its label revision to a consumption figure, then match that consumption to the actual account or lease calculation. Without those links, a precise-looking monthly quote is simply someone else’s assumption expressed in baht.

What is worth verifying

Evidence that makes an estimate auditable, not a guarantee of a future bill.

Model matches the label QR record

Why it mattersConnects label performance data to the installed unit, not a lookalike.

Bill shows tariff class and meter readings

Why it mattersProvides baseline kWh, Ft and the applicable billing route.

Monthly figure can be recreated from kWh and published tariff

Why it mattersReveals whether a simple per-unit quote conceals a different billing method.

Metered energy or a clearly labelled assumption range

Why it mattersReduces false precision, while short metering still cannot capture every season.

Expert view

Mark Erometskiy

I never treat the annual baht figure on an air-conditioner label as a quote for a tenant’s next electricity bill. The first useful evidence is the building’s actual billing method and the tariff class behind it. A strong efficiency rating helps compare similar equipment, but it cannot tell us how many kWh a sun-exposed apartment will use. A modest estimate backed by meter readings and clear assumptions is worth more than an attractive number with no route back to the bill.

Mark Erometskiy
NovAsia Thailand expert
Expert profile →

Sources and check dates

Sources5
  1. EGAT — Air Conditioner No.5 Label Programme Requirements, EGAT AC ED.5/01-2026 (May 2026)

    Current AC programme manual: label fields, model classes and seasonal testing including ISO 16358-1:2013. Annual cost assumes 2,920 h and THB 5.00/kWh (a 2023 price assumption), not the 2026 PEA bill rate.

  2. EGAT — The updated No.5 energy label explained (30 January 2026)

    January 2026 introduction of the revised No.5 label with six grades, a comparative annual baht estimate, efficiency information and a QR code.

  3. EGAT — Historical No.5 air conditioner calculation (2019 explainer)

    Historical comparison only: cooling-capacity/SEER formula, eight hours daily and THB 3.96/kWh. Superseded price assumption, not the current bill formula.

  4. PEA — Residential electricity tariff revision effective September 2026 (11 September 2026 notice)

    PEA class 1.1.2 from September 2026: first 200 kWh at THB 3.0000, 201–400 at 4.1584, over 400 at 4.3583, before Ft, VAT and service fees. The indexed announcement is available, but direct page retrieval was limited.

  5. PEA — Ft tariff adjustment for September–December 2026

    Confirms the Ft surcharge of THB 0.1623 per kWh for September–December 2026; a later billing period requires the applicable published rate.

A practical second opinion

Need help assessing a specific property?

Send the property link, price and your goal. We will separate the documented facts from the points that still need a property-specific check.

What to send: link, budget and target date